Workshop On Manufacturing Cages For Laying Hens With An Egg Collector

Workshop on manufacturing cages for laying hens with an egg collector

In the natural environment, a chicken nests for egg laying and nestling. Therefore, any chicken coop needs to be equipped with an analogue of the nest. The article discusses the features of cages that can be made with your own hands, gives detailed instructions on how to make cages for chickens with a photo and video that shows the manufacturing process.

Dimensions and construction

Tools and materials

Video “Homemade nest for laying hens”

Cell Features

With your own hands, you can build cages for laying hens, with any number of tiers, any area. The main thing is that the floor does not bend under the weight of the birds. In addition, it is worth providing all the necessary equipment for laying hens.

The video shows how to make a cage with an egg collector for broilers with your own hands.

There must be an egg collector in the cage. It is a sloping floor with a curved edge, equipped with a feeding device, a drinking bowl, a tray for collecting litter and waste.

When making a nest with your own hands, you need to think about lighting. Egg sock productivity is highly dependent on light. Even if there is natural light in the room, then it is definitely worthwhile to make additional lighting in the sockets. For this, several lamps with a dimmer are suspended, which will regulate the light intensity. The photo shows an example of additional lighting.

Workshop on manufacturing cages for laying hens with an egg collector

Dimensions and construction

Laying hens, which are intended only to lay eggs, are small in size, so it makes no sense to make a very large cage for them. When creating a drawing, you need to count on about 400 square meters per chicken. cm square cells. If chickens are bred to get both meat and eggs, then the maximum area must be increased to 750 square meters. cm per chicken.

Read more:  Bird Cages Selection And Equipment

The base of the cage is a regular frame made of wood or metal. For the floor and walls use a metal mesh. Often the dimensions of the nests are selected based on the materials that are at hand. Nest sizes are recommended for one layer – 50x50x65 cm, for 5-7 – 70x150x65 cm. A drawing is created based on the dimensions.

Workshop on manufacturing cages for laying hens with an egg collector

Section example for 2-3 chickens

It is undesirable to plant more than 6 goals in one nest, as this adversely affects the state of laying hens and complicates maintenance.

If there are a lot of chickens, then it is better to make more sections, but a smaller area. This is much better than one, but 3 meters.

Step-by-step instruction

Using the detailed instructions, a person who owns a tool and has at least a little carpentry experience can make nests for layers.

Tools and materials

Making a chicken cage is very simple, it does not require expensive materials, any special skills or tools. The framework will serve as the basis for the cell. It is more practical to make a frame of metal.

Thus, to create a cage for layers of materials you will need:

  • wooden beam or metal profile;
  • nails and screws;
  • tin sheet;
  • metal sheet for feeders;
  • metal mesh with honeycombs in the size of 2550 or 12525;
  • heck.

From the tools you need to take:

  • hammer;
  • hacksaw for wood or metal, depending on the choice of material;
  • pliers.

All materials and tools need to be prepared in advance so that everything is at hand while working.

Workshop on manufacturing cages for laying hens with an egg collector

Stages

First, to make a cage for laying hens, you need to build a frame. It must be made stable with additional stiffeners, which should be located at the bottom of the cage or wall.

Read more:  Paradise Place For Bird Cages For Budgies

Floor making

When installing the floor, you first need to make shelves. The drawing shows that one shelf is located horizontally, and the other is inclined 8 degrees. For the device of the pallet, a straight shelf is needed, and the tilted one is intended for the floor on which the eggs will roll into the collector. The shelf with a slope, according to the drawing, should protrude a little, approximately 12o mm forward. The distance between the straight and inclined shelves should be about 110 mm. This is done in order to conveniently place the pallet where the litter will be collected.

Next, the edge of the tilted shelf is bent so that as a result a groove is obtained. He will be needed to roll eggs on it. The depth of the gutter must be large enough for the eggs to roll along it and not fall out. Below is a drawing of the design of the socket.

Workshop on manufacturing cages for laying hens with an egg collector

Socket device drawing

Front wall construction

After making the floor, you can begin to create the front wall according to the drawings. This item is the hardest to assemble. On this wall there will be a feeder and a water tank. Layers need access to grain. The front wall also serves as a door for chickens.

There are several types of how to build it:

  1. If the cage is not very wide, then the front wall must be completely made a door. It can be built from a grid, which should be hung on a loop. Then equip the heck. In this case, the mesh must be selected with large cells, so that chickens have access to feed.
  2. If the cell is wide, then the front wall should be solid. Then the door should be centered.
  3. If the tiers are at a sufficient distance from each other, hens can be reached through the ceiling. In this case, the doors are not needed. They make it from a grid, which is placed on top and fixed with removable latches.
Read more:  Vintage Wedding Bird Cage

Workshop on manufacturing cages for laying hens with an egg collector

Drinking bowls, feeders and other elements

Feeders and water containers are made by hand by bending the prepared metal sheets. Then they are hung on the front doors. A nipple device that is equipped with small bowls can serve as a replacement drinker. This device is much more convenient and safer.

According to the drawings, pallets are made of tin and set up for chickens. It is necessary that they be conveniently periodically cleaned, disinfected. If you plan to place chickens on the street in the summer, then it is better to make the roof with your own hands from available material, such as a slate sheet, a piece of tarpaulin or linoleum.

Photo gallery

Video “Homemade nest for laying hens”

This video demonstrates how to build a cage with your own hands.

Pin It on Pinterest

Share This